The mono band antenna does not require the assistance of balun, and they are made from coaxial wires that could emit fifty ohms. The shield split is located in the middle, and their feed lines are connected to open edges. The client is advised not to break the conductor located in the center.
The attachment of the open ends plays the role of a half wave duple, which can be separated into various sections to allow the frequencies to work properly. The bazooka antenna is independently connected to a leveled surface that could endure restrictions and the multi band cable only functions after an effective tuning. This cable is an inexpensive substitute, since ground radials and coils are not needed.
The product can also be associated in a previously installed feed line, thus making them efficient, and these materials are twistable that they can be positioned in car trunks. They are equipped with the ability to function similarly to the half wave antennas that a client could easily build various types of this tool. Their wires are constructed by casting a little amount of electrical wavelengths located at the coaxial exterior layer.
The lead found at the center of its coax shapes half of the dipole and the other half is supplied by the plaits. This composition makes a cable a device with a low pattern of radiation and an obstruction of 55-60 ohms. The braids are the main feature, since they help in reducing the amount of feed line radiation, and they end up shorter in size compared to other elements.
The size is brought forth by the contact of the plaits and coax wires, and the braids found on the inner and outer part mixes to form the balun. The items required to produce a cable are the following, the specific length of heat deflating tube, coaxial, and the adaptor that could fit the radio. The procedure starts by removing the coax outer portion for the insertion of a top section, and followed by the flicking of the braided back over the covering till it ends at the lower mark.
The braid and uppermost portion is snipped to a specified size after the spin. A calculation is done to reach the particular length of coaxial to be sliced, and this makes the cover. A client should remember that they should not make cuts in the plaits.
The cutting of the coaxial that could produce a lengthwise slit in the jacket follows, and the removal of these sections exposes a braid. Afterwards, the plait needs to be flipped, and followed by gently removing the braid from the insulation and move it to the inner conductor. Grab two inches aloft the uncovered section and force it against the coax found in the short sections, after letting it loose.
Tightly hold the plaits over the covering and place an adhesive tape to place it in place at the lowest portion, and trim it to a specific length. Get the tube and cut it into pieces to serve as the protection for the feed point and plaits, and position the wires with a glue gun or hair dryer. Emergency models of this product is built from the remaining wires from the coax.
In building a standalone model, it is advised to cut the enough length of wires underneath the plait and have it connected to its conductor. The installment of an effective adapter to the radio and feed line is the last step. Tuning follows after the construction of this antenna.
The attachment of the open ends plays the role of a half wave duple, which can be separated into various sections to allow the frequencies to work properly. The bazooka antenna is independently connected to a leveled surface that could endure restrictions and the multi band cable only functions after an effective tuning. This cable is an inexpensive substitute, since ground radials and coils are not needed.
The product can also be associated in a previously installed feed line, thus making them efficient, and these materials are twistable that they can be positioned in car trunks. They are equipped with the ability to function similarly to the half wave antennas that a client could easily build various types of this tool. Their wires are constructed by casting a little amount of electrical wavelengths located at the coaxial exterior layer.
The lead found at the center of its coax shapes half of the dipole and the other half is supplied by the plaits. This composition makes a cable a device with a low pattern of radiation and an obstruction of 55-60 ohms. The braids are the main feature, since they help in reducing the amount of feed line radiation, and they end up shorter in size compared to other elements.
The size is brought forth by the contact of the plaits and coax wires, and the braids found on the inner and outer part mixes to form the balun. The items required to produce a cable are the following, the specific length of heat deflating tube, coaxial, and the adaptor that could fit the radio. The procedure starts by removing the coax outer portion for the insertion of a top section, and followed by the flicking of the braided back over the covering till it ends at the lower mark.
The braid and uppermost portion is snipped to a specified size after the spin. A calculation is done to reach the particular length of coaxial to be sliced, and this makes the cover. A client should remember that they should not make cuts in the plaits.
The cutting of the coaxial that could produce a lengthwise slit in the jacket follows, and the removal of these sections exposes a braid. Afterwards, the plait needs to be flipped, and followed by gently removing the braid from the insulation and move it to the inner conductor. Grab two inches aloft the uncovered section and force it against the coax found in the short sections, after letting it loose.
Tightly hold the plaits over the covering and place an adhesive tape to place it in place at the lowest portion, and trim it to a specific length. Get the tube and cut it into pieces to serve as the protection for the feed point and plaits, and position the wires with a glue gun or hair dryer. Emergency models of this product is built from the remaining wires from the coax.
In building a standalone model, it is advised to cut the enough length of wires underneath the plait and have it connected to its conductor. The installment of an effective adapter to the radio and feed line is the last step. Tuning follows after the construction of this antenna.
About the Author:
Our website is your main source for the best quality bazooka antenna. For further info, click the link that appears here http://ultimax-antennas.com.
0 komentar:
Post a Comment